1. gogorocky's Avatar
    step 1.Take apart phone.

    Pls open 2 screws at the bottom with the blue star screwdriver.

    Note: Don't lose the screws.


    Step 2. Remove the back cover.

    After Carrying down the screw,pls press the back cover with your hand and push up it like the picture showed.And then open the back cover.


    Step 3. Pls don't tamper anything after carrying down the cover.


    Step 4. Take apart the screws.

    As shown in picture,there are 5 screws.Because different screws have different size in different colored circle.

    Pls mark the sequence of screws when u take apart them.


    Step 5. Take away the iron sheet.

    After carrying down the screws,prize up the black iron sheet slowly with tweezer as shown in picture.

    Note: Don't prize up with wrong way.


    Step 6.Take away the iron sheet and put aside.Don't crush this iron sheet.


    Step 7. Open stand.

    Once opened the iron sheet,we can see 5 dock. Pls remove the rightmost green stand and blue stand slowly.


    Step 8.This is the picture that removed the green stand and blue stand.


    Step 9. The Luminescent way.

    One is weld the red cable directly.Another is fix the red cable with 3M.

    The first way:According to the width of two stand,pls cut down 3M sticker and then stick in the middle of dock.The area of 3M play the insulation role.Don't cover the golden finger on the two side of cable.
    03-21-2012 02:49 AM
  2. gogorocky's Avatar
    Step 10. Stick the 3M glue.

    Contact to the yellow spot with the red cable. It must contact the spot and the Luminescent light will be shined.

    The way of 4S is the same as 4G.Only different welding spot.

    Note: Don't install wrong screws when 4S install.


    Step 11. Fixed.

    Once contact the red cable, fix the red cable and yellow adherent point with 3M.



    Step 12.The slip must press the touch contact.

    Cut a 4*4mm slip and stick on the 3M to press the red cable and yellow spot.The yellow cable connect to the screw. Pls check the light whether luminescent normally or not. If no,is that have not connect the adherent point well.Pls try to connect it well.



    Step 13. Second way:Welding.

    Weld red cable on the yellow welding spot and yellow cable connect the screw.

    Note:Pls ask for management master who are professional to weld. Otherwise, it is easy to weld damaged the component.

    After welded,if the light is dispalay normally,pls stick the 3M which play the insulation role.


    Step 14.Fix the light.

    Cut the sponge into strand to fix the light.Pls pay attention to the light should be under the logo.The position of sponge and cable will be influent the cover and cause gap.


    Step 15.Install teh iron sheet.

    As shown in picture,there are 5 screws.Because different screws have different size in different colored circle.Pls pay special attention to the screws.Don't screw the wrong screws in wrong position.Otherwise,it will damage the screen.Among the 5 screws,First step is screw the green one which is the longest hole site .Second is the red screw which is the biggest hole site.Third is the yellow which is the smallest.Fourth is the two remaining screws.the size of these two screws is the same.If different,pls install the small one on the side of flashlight.Another install in the rightmost hole.

    Note:Pls install the screws after making yourself clear what described above.



    Step 16. install the back cover


    Step 17. And then pull up the cover to the bottom.


    Step 18. screw the screws.


    Step 19. Ok,The impression
    drawing is out.The picture is the effect that have not tear off the blue film.If u don't like blue,pls take away the blue film.

    You can order the iPhone 4/4S Logo Mod Kit LED from Eachsupplier.com
    03-21-2012 02:50 AM
  3. ame's Avatar
    THAT freaks me out.
    03-21-2012 08:40 AM
  4. GingerSnapsBack's Avatar
    THAT freaks me out.
    I'd be scared I'd blow up my phone.
    03-21-2012 09:47 AM
  5. ThePinkChameleon's Avatar
    Yea, lol. I'd never attempt this either !!
    03-21-2012 01:58 PM
  6. BLiNK's Avatar
    you guys sound like a bunch of old women

    if you're out of warranty, and really want to do it, why not?
    03-21-2012 02:04 PM
  7. ThePinkChameleon's Avatar
    you guys sound like a bunch of old women

    if you're out of warranty, and really want to do it, why not?
    hey we are women yes, but old?!?! no way !!
    03-21-2012 02:07 PM
  8. ame's Avatar
    Considering the luck I've had with 4S' I think I don't need to introduce any new drama!
    03-21-2012 03:09 PM
  9. ThePinkChameleon's Avatar
    Considering the luck I've had with 4S' I think I don't need to introduce any new drama!
    lol, THIS definately applies to you Ame
    03-21-2012 05:49 PM
  10. ame's Avatar
    lol!

    Im scared sh1tless to put a good screen protector on it.
    03-21-2012 09:13 PM
LINK TO POST COPIED TO CLIPBOARD